TO:  Multi-Tech Products

I am repair technician and I can never achieve a hidden repair with your MMA system on acrylic.
My filler and contour application is perfect, but I always have a dark ring effect around the repair area after buffing.
I know factories use this product to get perfect repairs. What do they do differently? One factory even sends me the color. So I know it is the right color.
What am I doing wrong?  See photo.

John

Repair Technician

photo

 

 

 

 

 

 

Hello John,

This is one of the most common questions from repair technicians about achieving the perfect repair with our MMA System on acrylic bath and shower repairs.   The simple answer is the Clear Coat must be used.  Many technicians don’t understand the functions and importance of the clear coat, and therefore they think it is not necessary.

Some bath ware manufacturers send  only the product color coating (base coat) to technicians for warranty repairs. This certainly helps the contracted technician to use the proper color, but it might give the impression that only the base coat is needed for the repair.  I would also believe the customer service representative may not understand all of the requirements, as well.  However, the clear coat plays a role in both the dark ring, and the endurance of the repair.  The dark ring you mention develops when the base coat is sanded and polished without the presence of Clear Coat.

Since the MMA Basecoat is highly pigmented, it is not designed to withstand dirt, soap and general bath and shower environment usage.  Over a short period of time, the repair zone without Clear Coat will change color and become stained.  The Clear Coat is formulated to seal the base coat and give the repair its hardness, UV protection, and longevity.

How to remove the dark line?

With a good color match to the surface, the dark line will disappear when the Base coat color is sprayed on to the surface. This is done by  blending (feathering) the outer ring of the color application with the airbrush and spray process.  The dark ring appears, again, when the base coat is sanded. The sanding process  removes the hiding ability of the blend-out of the spray.  The clear coat, applied over the sanded base coat, can not remove the dark line. The clear coat must be sprayed over a “blended and without being sanded base coat”.  This will seal the feathered affect, and hide the dark line. Then the clear coat is sanded and polished. But the clear coat cannot be sanded excessively to remove the coatings, entirely.  The clear coat will then protect the colored base coat, and leave the blended area undisturbed.

Typically, this does not happen with gel coat repairs. Why does it happen on acrylic repairs?

Acrylic is a translucent material composed of a clear polymer with pigments added to achieve the desired color.  When compared to acrylic, gel coat is a resin with a higher loading of pigment.  Acrylic products are made by vacuum forming a flat sheet, heated to a high temperature, into the desired shape.  A highly loaded acrylic resin would be more brittle, and less able to be thermoformed.  Whereas, gel coat is sprayed onto a mold surface, so it can be highly loaded with pigment as long as it can be sprayed.  Higher-priced products are made from acrylic, since it is superior in properties needed for bath ware and spas compared to gelcoat resin.  When repairing a surface, a coating is used to match the color of the product.  It is sprayed over the repair filler and it’s adjacent area.  When the coating is applied to an acrylic surface, it creates a shadow at sharp, delineated edges of the coating. This is due to the thickness and transparency of the acrylic.  Even with a good repair base coat color match,  a dark halo is cast around the repair when sanded.  The only way to address the shadow casting effect, is to blend(feather) the base coat color, and apply (spray) a clear coat over it for protection and to preserve the appearance.

How to “blend” or “feather” the MMA base coat?

A single action (important) air brush operating at 35 psi (1 cfm air source) at the gun is required.  First, spray the base coat sufficiently to cover the filler area. This may take several layers (see MMA instructions).  Then open up the airbrush spray pattern to allow a higher volume of product to be sprayed. Using the correct temperature thinners and a smooth spray-out from the gun, pull the gun away (6-8 inches) from the spray surface, and feather coat the base coat around the edges of the previous sprayed area. Try to achieve a smooth surface that hides the edges of the over-spray.  If the product has sprayed a little dry and the surface around the area looks dull, wet-out those areas with straight MMA Finishing solvent from the gun in a clean separate jar. Do not over flood the area. Allow the coating and Finishing solvent to evaporate  (dry) before clear coating. This is the procedure required to create undetectable repairs on surfaces.  This spot repair technique also works with our Quick Glaze Systems.

Here is a summary of the important reasons to use Clear Coat over MMA Basecoats:

-Clear Coat seals the base coat color to retain its match and blend (feather effect) during the sanding and buffing process.
-Clear Coat is imperative for gloss and wear protection.
-Clear Coat adds depth to the acrylic look and effect matching the original surface.
-Clear Coat seals the color coat so it will not absorb detergents, dirt and elements from hard water.(most important) -Clear Coat is a necessary system component formulated and designed to be used with every MMA Basecoat application.

Other important MMA System components and tips are:

-The proper airbrush (Single action) 35 psi at the gun with a 1 cfm air source. Very important.
-Use MMA System Thinners, only. Alternative thinners will effect spray performance and final color.
-Use proper rated temperature thinners for ambient working conditions. The wrong thinner selection can cause dry spray out.
-Note: MMA Basecoats will darken as they dry. Decide on color adjustments after it dries.  Light forced heating is okay.
-Sanding can be performed on base coats, but reapply the base coat and perform the feathering prior to Clear Coating.

Here is a link to the MMA System repair instructions.

http://www.acrylicfiberglass.com/Procedures/BATH-REPAIR-MMA.pdf

Rob Clos

President

 

Advertisements